A burner that will not light, an electric element that stays cold or glows unevenly, an induction surface that will not recognize cookware, or a control panel that will not respond usually points to one failed part rather than a worn-out cooktop.
Electric Or Radiant Element Not Heating
On electric cooktops, a coil or radiant element that no longer heats is usually the element itself, but a worn infinite switch or damaged wiring behind the panel can cause the same symptom and is worth ruling out before the element is replaced. On glass cooktops, a cracked or unevenly worn element can also show up as a hot spot or an element that never gets fully hot. On induction models, a surface that will not detect cookware or shuts off during use can point to a sensor or board fault rather than the cooktop itself.
Gas Burner Clicking But Not Lighting
On gas cooktops, a burner that clicks steadily but never lights usually has a weak igniter that cannot draw enough current to open the gas valve. A burner valve problem can also cause a weak, uneven, or lazy flame. If you ever smell gas near the cooktop, do not try to light it or attempt any repair. Leave the home and call the gas utility from outside.
A few checks are safe to do yourself before calling for service. Confirm the breaker for the cooktop has not tripped, make sure knobs are fully seated and turning freely, and check that nothing is blocking an induction surface's sensors. These checks rule out the simplest causes without opening the appliance.
Stop and call a technician if a breaker trips repeatedly when the cooktop is used, if you see scorching or melted insulation near the wiring or terminal block, or if there is any smell of gas. Call (615) 412-2497 if you notice any of that, since those are signs the wiring, connection, or gas supply needs a proper inspection rather than a do-it-yourself fix.
Diagnosis starts with testing the specific part, such as the igniter, element, switch, or control board, rather than replacing parts by guesswork. Having your model number ready when you call helps us narrow down the likely part before the visit. If the burners are on a freestanding range, oven and range repair covers the oven side too.
Middle Tennessee's storm season brings brief power flickers that can trip a touch-control or induction cooktop's board without tripping the breaker itself, which is one reason a panel can stop responding right after a storm even though the wiring is fine. Older Nashville and Davidson County homes with dated electrical panels are also more likely to have a breaker that is marginal for a cooktop's draw, so a breaker that trips repeatedly under normal use is worth having checked rather than reset again and again. If every element is dead and the breaker keeps tripping, see appliance power problems.
For cooktop repair in Nashville, Davidson County, and the surrounding Middle Tennessee area, call (615) 412-2497.
Technician insight
A common mix-up with cooktop repair is assuming a dead burner or element means that part has failed, when the real issue is sometimes a worn switch or a wiring fault feeding it. Testing the switch and wiring first avoids replacing a part that was never the problem.
One side of an electric cooktop stops heating
A common call: one element on an electric cooktop stops heating while the rest of the cooktop still works. Testing sometimes finds the element itself has failed, and other times traces the problem back to the switch or wiring feeding that element.
Cooktop Repair Services We Offer
✓Gas Cooktop Igniter Repair
A weak or cracked spark igniter is replaced after testing confirms it can no longer open the gas valve reliably, which prevents the burner from lighting.
✓Electric Cooktop Element Replacement
A coil or radiant element that no longer heats evenly is tested for continuity and voltage before being replaced.
✓Control Board Diagnosis and Repair
Main or touch control boards are tested and replaced when a panel stops responding or shows a fault that testing traces back to the board.
✓Burner Valve and Manifold Service
Valves that cause an uneven, weak, or lazy flame on a gas cooktop are cleaned or replaced after the burner and manifold are inspected.
✓Induction Cooktop Sensor Repair
Sensor and board faults that stop an induction surface from detecting cookware are tested and addressed so the surface responds correctly again.
✓Knob Switch and Wiring Repair
Worn switches and damaged wiring that prevent a burner or element from activating correctly are tested and replaced.
How it works
- 1
Initial Inspection
The technician verifies power or gas supply before testing each burner or element in sequence.
- 2
Component Testing
Igniters, valves, elements, switches, and control boards are checked with a multimeter to isolate the exact fault.
- 3
Explanation Of Findings
The failed part and the repair needed are explained before any work proceeds.
- 4
Repair Completion
The part is installed or ordered, and the cooktop is tested under normal use before the technician leaves.
Pricing
Cost depends on which part has failed, such as an igniter, element, switch, or control board, and whether a replacement part needs to be ordered. We explain what we find and what the repair involves before any work starts.